Product Category: Tile Adhesive

Tile Shield Epoxy Tile Grout is a premium, high-performance, two-component, resin-based epoxy grout specifically designed for use in both residential and commercial tile installations. It provides outstanding protection against stains, moisture, chemicals, Acid and dirt, making it ideal for high-traffic areas, wet spaces, and environments exposed to heavy-duty use.

Key Features

• High Strength and Durability: Offers superior bond strength, ensuring long-lasting performance.
• Waterproof and Stain-Resistant: Perfect for use in high-moisture areas like kitchens, bathrooms, and pools.
• Chemical Resistant: Resists a wide range of chemicals and cleaning agents, maintaining grout appearance and integrity.
• Easy to Clean: The smooth surface resists dirt, stains, and grime buildup, making cleaning effortless.
• Flexible and Versatile: Suitable for use with ceramic, porcelain, stones and other types of tiles.
• Non-Shrink and Non-Cracking: Ensures consistent joint integrity even under extreme conditions.

Preparation and Application Instructions

1.  Surface Preparation

• Ensure that the surface to be grouted is clean, dry, and free of any contaminants, such as dirt, dust, grease, or old adhesive residues.
• Remove any excess water or moisture from the substrate. Ensure the joints are clean and free from debris. Use a vacuum or a brush to clear the grout joints.

2. Mixing

• Mix Component A (epoxy resin) and Component B (hardener) in the correct ratio (as indicated on the packaging) until a uniform color and consistency is achieved.
• Ensure the mixture is free from lumps and thoroughly blended for optimal performance.
• Mix only the amount of grout that can be applied within the pot life (30-45 minutes).

3. Application

• Use a rubber float or grout applicator to apply the grout into the joints, pressing firmly to ensure full joint coverage.
• Remove excess grout using the float at a 45° angle to avoid disturbing the joints.
• Allow the grout to set for 15-30 minutes before cleaning excess residual with a damp sponge.
• Clean the surface with a damp sponge, rinsing frequently to ensure the surface is smooth and free of grout haze.

4. Curing

• Allow the grout to cure for a minimum of 24 hours before subjecting it to any traffic or water exposure.
• Full curing time may extend up to 48 hours, depending on the ambient temperature and humidity.

Health and Safety

Precautionary Statements

• Causes serious eye irritation.
• May cause an allergic skin reaction.
• Keep out of reach of children.
• In case of contact with skin or eyes, rinse immediately with plenty of water for at least 15 minutes and seek medical attention if irritation persists.
• Wear protective gloves, protective clothing, and eye protection.

First Aid

• Skin Contact: Wash thoroughly with soap and water.
• Eye Contact: Rinse immediately with plenty of water and seek medical attention.
• Inhalation: Move to fresh air. Seek medical attention if symptoms persist.

Tile Bond A+ is a high-performance cementitious tile grout enhanced with a special admixture that improves adhesion, water resistance, and flexibility. It is ideal for filling tile joints in both interior and exterior applications, providing superior crack resistance and durability. Tile Bond A+ is suitable for use with ceramic, porcelain, vitrified, and natural stone tiles.

Key Features

• Enhanced adhesion with special admixture for improved bonding strength.
• Superior water resistance and flexibility.
• Crack-resistant, shrinkage-controlled formulation.
• Suitable for joint widths up to 6 mm.
• Excellent stain resistance.
• Available in multiple colors.
• Suitable for both interior and exterior applications.

Surface Preparation

• Ensure the tile joints are clean, dry, and free of dust, grease, or contaminants.
• The tile adhesive should be fully cured before applying Tile Bond A+ grout.
• Use a vacuum or soft brush to remove any debris from the joints.

Mixing Instructions

• Mix Tile Bond A+ powder with clean water (approx. 300-350 ml per 1 kg of powder).
• Stir using a slow-speed mixer until a smooth, lump-free paste is obtained.
• Let the mix stand for 2-3 minutes and then remix.
• Use the mixture within 45-60 minutes for optimal performance.

Packaging

• Available in 1 kg, 5 kg, and 10 kg bags

Health & Safety

• Use protective equipment, including gloves and masks, while handling.
• Avoid inhalation and contact with skin and eyes.
• In case of contact with eyes, rinse immediately with plenty of water and seek medical advice if necessary.

White tile adhesive is a high-quality polymer-modified cement-based adhesive designed for fixing ceramic, porcelain, and natural stone tiles on walls and floors. It offers excellent adhesion, flexibility, and water resistance, making it suitable for both interior and exterior applications.

Key Features

• Excellent adhesion to various substrates (concrete, plaster, cement boards, etc.).
• Suitable for thin-bed and thick-bed applications.
• Water-resistant and non-slip properties.
• Good open time and adjustability.
• Polymer-modified for enhanced flexibility and durability.
• Free from harmful substances, environment friendly.

Application Guidelines

1. Surface Preparation

• Ensure the substrate is clean, dry, and free from dust, grease, or loose particles.
• For highly absorbent surfaces, pre-wet the substrate with water.

2. Mixing

• Add clean water to a mixing container (approximately 6-7 liters per 20 kg bag).
• Gradually add the adhesive powder and mix mechanically until a lump-free with hand stirrer till homogeneous paste is achieved.
• Allow the mixture to rest for 5-10 minutes, then remix before use.

3. Application

• Apply the adhesive using a notched trowel (notch size depends on tile size).
• Comb the adhesive in one direction for better air release.
• Press the tiles firmly into place and adjust within the open time.
• For large-format tiles, apply adhesive to both the substrate and the back of the tile (Buttering).

4. Curing

• Allow 24 hours for initial curing before grouting.
• Full strength is achieved after 7-14 days, depending on environmental conditions.

Compliance and Standards

• Complies with ISO 13007 (C2TE classification for cementitious adhesives).
• Meets EN 12004 standards for tile adhesives.

Limitations

• Not suitable for continuously submerged areas (e.g., swimming pools).
• Avoid application in temperatures below 5°C or above 35°C.

Cementitious Tile Grout is a specially formulated grout designed for filling joints between ceramic tiles, porcelain, and stone. It offers excellent durability, water resistance, and stain resistance, making it suitable for both interior and exterior applications. Available in a variety of colors to enhance the aesthetic finish of tiled surfaces.

Key Features

• High bonding strength
• Resistant to water and moisture
• Crack-resistant and shrinkage-free
• Suitable for joint widths up to 5mm
• Available in multiple colors
• Easy to apply and clean
• Suitable for interior and exterior use

Surface Preparation

• Ensure the tile joints are clean, dry, and free from dust, grease, or other contaminations.
• Tile adhesive must be fully removed before applying grout.
• Use a vacuum or soft brush to remove dust or debris from the joints.

Mixing Instructions

• Mix Cementitious Tile Grout powder with clean water (approx. 3.0-3.5 liters per 10 kg bag).
• Stir the mixture using a slow-speed mixer until a smooth, lump-free paste is achieved.
• Allow the mix to rest for 2-3 minutes and then re-mix before use.
• Use the mixture within 45-60 minutes.

Packaging

• Available in 1 kg in pouch and 20 kg bags.

Application Guidelines

• Apply the grout using a rubber grout float, ensuring joints are filled completely.
• Work diagonally across the joints to minimize air pockets.
• After 10-15 minutes, clean off excess grout from the tile surface with a damp sponge.
• Allow grout to set for 24 hours before subjecting the area to light traffic or moisture.

Health & Safety

• Use personal protective equipment such as gloves, masks, and goggles during application.
• Avoid contact with skin and eyes.
• In case of contact, rinse immediately with plenty of water and seek medical advice if necessary.

TILEFIX-FT a polymer-modified, cement-based adhesive designed for tiles from 3mm to 10mm. Suitable for all types of vitrified and PVT & GVT tiles, it sets to a hard, durable, and water-resistant finish, making it ideal for both interior and exterior applications.

Application

Ideal for all types of vitrified & ceramic tiles surfaces. This product is waterproof making it suitable for both internal and external applications, including kitchens, bathrooms and shower enclosures, swimming pools. In fully immersed locations, the inclusion of an acrylic latex additive in the grout mix can enhance water repellent properties. Quick and easy to apply, providing a smooth substrates which is unaffected by water or weather. See Technical Data Sheet for mixing instructions.

Bonding the following types of tiles

• Ceramic
• Vitrified
• Earthenware
• Glazed
• Porcelain
• Stoneware
• Terrazzo
• Unglazed
• Thin and large tiles

Product Declaration

• C2T* according to EN 12004-1
• C2T* according to ISO 13007-1

*Tensile adhesion strength test after freeze-thaw cycles not conducted due to tropical climatic conditions.

Chemical Base

Portland cement, selected aggregates, water retention additives, re-dispersible polymer

Storage Conditions

The product must be stored in original, unopened, and undamaged sealed packaging in dry conditions at temperatures between +5 °C and +35 °C.

Shelf Life

18 months from date of production.

Tensile Adhesion Strength

Initial / dry condition	≥ 1.0 N/mm2
After water immersion / wet condition	≥ 1.0 N/mm2
After heat aging	≥ 1.0 N/mm2
After > 20 minutes, open time	≥ 0.5 N/mm2

Slip Resistance

≤ 0.5 mm

(EN 12004-2 / ISO 13007-2)

Mixing Ratio

Packing	Water to powder ratio by weight	Quantity of water per bag
20 kg	0.25–0.28	6.25–7.00 L

Fresh Mortar Density

1.8 ± 0.2 kg/L

Layer Thickness

3 mm min

Ambient Air Temperature

+5 °C min. / +45 °C max.

Substrate Temperature

+5 °C min. / +45 °C max.

Maturing Time

15 minutes

Pot Life

≥ 180 minutes (100 g mass, +27 °C).

Open Time

> 20 mins

(EN 12004-2 / ISO 13007-2)

Adjustability Time

40 min (+27 °C)

Applied Product Ready For Use

Use	Waiting Time
Grouting Floors / Walkable	24–38 hours
Grouting Walls	4–6 hours
Water immersion	21 days

Values determined in laboratory conditions: +23 °C ±2°C, R.H. 50 % ± 5 %. Higher temperatures will reduce the indicated waiting time, lower temperatures increase waiting time.

Consumption

Consumption is dependent on the substrate, surface profile, roughness, size of the tiles, the joints between them and application technique (i.e. single spreading / floating method or double spreading / buttering method). Apply product to a test area to calculate the exact consumption for the specific substrate conditions and proposed application.

As a guide for a single adhesive layer

Size of Tiles	Notched Trowel Size	Consumption of Dry Powder
Small	6 mm	3.00–3.50 kg/m2
Medium	8 mm	3.75–4.25 kg/m2
Large	10 mm	4.75–5.25 kg/m2

Mixing

Important: Avoid over-mixing to minimize air entrainment.

Requirement: Use a low-speed electric single paddle mixer (< 500 rpm) with spiral paddle for mixing.

• Pour the minimum recommended quantity of clean cold water into a clean mixing container.
• Gradually add the non-slip powder to the water while mixing.
• Mix thoroughly for ~5 minutes until a uniformly smooth mix is achieved. Add additional water, if necessary, to the maximum specified amount.
• Do not mix for 5 minutes to allow the mixed product to ‘mature’.
• Remix for 15 seconds.

Application

Important:

Apply sufficient adhesive to ensure adequate ‘wetting’ of the backs of the tiles.

Coverage on the back of the tiles must be 100 %.

Tiling must be carried out on freshly applied adhesive. Exert adequate pressure to ensure 100 % complete and uniform contact with the adhesive to achieve optimum adhesion.

If a skin forms on the surface of the adhesive, immediately remove the adhesive layer with a trowel, discard material and apply a fresh layer of adhesive.

Protect freshly applied material from freezing conditions and rain, etc.

For natural stone tiles, always carry out a preliminary test application first.

Note:

On cementitious substrates, the product can be used for laying non-absorbent tiles indoors up to 8 ft2 (e.g. 2 ft × 4 ft). On walls up to 8 ft height, non-heated floors, and outdoor applications up to 4 ft2 (e.g. 2 ft × 2 ft).

For tiles > 900 cm2 (e.g. 30 × 30 cm), the double-spreading (buttering) technique is always recommended.

• Apply sufficient adhesive to the prepared fixing surfaces with the flat side of the trowel.
• Comb additional adhesive with appropriate square notched trowel to the required bed thickness.
• Wherever needed (for large tiles), back butter the tiles for full bedding.
• Place tiles into wet, sticky adhesive and use a rubber mallet to fully embed the tiles.
• Adjust tiles if required. Provide support wherever needed.
• Clean off surplus adhesive from the tile face and between tile joints before the adhesive has dried.

TILEFIX-WT is a polymer-modified adhesive designed specifically for wall tiles in interior and exterior applications. It is ideal for vertical (wall) installations over cementitious substrates. Supplied as a dry-mix mortar, it requires the addition of water prior to application. This adhesive is highly effective for fixing ceramic and vitrified tiles, as well as heavy marble and granite, even on dense and smooth concrete surfaces.

Key Features

• Suitable for fixing ceramic tiles PVT & GVT for floor & wall.
• Polymer-modified adhesive.
• Good strength for interior situations.
• Easy mixing & application.
• NSA SILVER meets the adhesion requirements of ISO 9001:2015 “Specification for Adhesive for use with Ceramic PVT & GVT Tiles.”
• Self-curing properties, which allows for no-hassle application with minimum labor.
• The free-flowing product makes it easier to mix and apply.
• No-sag formula: provides hassle-free application on vertical walls, without any slippage.
• Very low shrinkage prevents de-bonding and gives longer life to tiles.
• Useful for bed thickness of 3-10 mm; may go up to 15 mm to a limited extent, as per required applications.

Chemical Base

Portland cement, polymers, and selected aggregates.

Shelf Life

18 months from date of production.

Storage Conditions

The product must be stored in original, unopened, and undamaged sealed packaging in dry conditions at temperature between +5 °C and +35 °C.

Tensile Adhesion Strength

≥ 0.5 N/mm2

EN 12004-2 / ISO 13007-2

Mixing Ratio

Packing	Water to powder ratio by weight	Quantity of water per bag
20 kg	0.22–0.24	4.4–4.8 L
40 kg	0.22–0.24	8.8–9.6 L

Fresh Mortar Density

1.8 ± 0.2 kg/L

Layer Thickness

3 mm min.

Ambient Air Temperature

+5 °C min. / +45 °C max.

Substrate Temperature

+5 °C min. / +45 °C max.

Maturing Time

15 minutes

Pot Life

110 minutes

(EN 12004-2 / ISO 13007-2)

Open Time

> 10 minutes

(EN 12004-2 / ISO 13007-2)

Adjustability Time

8 minutes

Applied Product Ready For Use

Use	Waiting Time
Grouting Floors / Walkable	24–36 hours
Grouting Walls	4–6 hours
Full Traffic	14 days

Values determined at laboratory conditions: 23 °C ± 2 °C, R.H. 50 % ± 5 %. Higher temperatures will reduce the indicated waiting times, lower temperatures increase them.

Important

Protect from adverse weather conditions, such as extremely high or low (freezing) temperature, rain, for at least 12–24 hours from application.

Consumption

Consumption is dependent on the substrate, surface profile, roughness, and application technique. As a guide for a single adhesive layer:

Size of Tiles	Notched Trowel Size	Powder Consumption
Small	6 mm	4.0–4.5 kg/m2
Medium	8 mm	5.4–6.0 kg/m2
Large	10 mm	7.5–8.0 kg/m2

Coverage

Pack	Area Covered
20 kg	34–40 sqft for 3 mm thickness
40 kg	70–80 sqft for 3 mm thickness

Cleaning of Tools

Clean all tools and application equipment with water immediately after use. Hardened/cured material can only be removed mechanically.

Mixing

• Pour the recommended amount of clean normal water into a suitable, clean mixing container.
• Slowly add the powder to the water and then mix thoroughly using a low speed (< 500 rpm.) drill mixer until the material is fully mixed and lump free. Avoid entraining air into the mix by over mixing.
• Allow the product to mature for 3-5 minutes before remixing for 30 seconds. The finished mix has a creamy consistency uniformly colored and is easy to apply and spread.

Application

Important

Avoid application in direct sunlight and/or strong wind / draught.

• TILEFIX-WT is applied using a suitable square notched trowel. Apply adhesive to the prepared fixing surface with the appropriate trowel and comb to the required bed thickness. Coverage on the back of the tiles should be 100 %.
• Tiling must be carried out on freshly applied adhesive, exerting adequate pressure to ensure complete and uniform contact with the adhesive for optimum bond.
• If a skin forms on the surface of the adhesive, immediately remove the adhesive layer with the trowel, discard material and apply a fresh layer of Tile Fix-WT adhesive.
• Adjust tiles if required.
• Clean off surplus adhesive from the tile face and between the tile joints before the adhesive has dried.
• After the required waiting time apply the appropriate grout into the tile joints.
• Tile-fix WT is ideal for laying absorbent ceramic and vitrified tiles up to 900 cm2 (e.g. 30 × 30 cm), for indoor application only. Tiles > 900 cm2 (e.g. 30 × 30 cm), the double-spreading (buttering) technique is always recommended.

TILEFIX -AT a Polymer Modified Cement Based adhesive designed for Tiles from 3 mm to 10 mm. Suitable for all types of Ceramic, Vitrified, PVT, GVT, Marble, Granit. All types of stones. It sets to a hard durable and water-resistant finish, making it ideal for both interior and exterior applications.

Bonding the following Types of Tiles

• Ceramic
• Vitrified
• Earthware
• Glazed
• Porcelin
• Stoneware
• Terrazzo
• Unglazed
• Thin and large tiles

Product Declaration

• C2T according to EN 12004-1
• C2T according to ISO 13007-1
• Tensile adhesion strength test after freeze-thaw cycles not conducted due to tropical climatic conditions.

Chemical Base

Portland Cement selected aggregates, water retention additives, re-dispersible polymer.

Tensile Adhesion Strength

Initial/dry condition	≥1.0 N/mm2
After water immersion/wet condition	≥1.0 N/mm2
After heat aging	≥1.0 N/mm2
After+20 minutes, open time	≥0.5 N/mm2

Slip Resistance

≤0.5 mm

(EN 12004-2/ISO 13007-2)

Mixing Ratio

Packing	Water to powder ratio by weight
20 Kg	0.25-0.28
40 Kg	0.25-0.28

Quantity of water Per bag

20 Kg	6.25-7.00 L
40 Kg	12.50-14.00 L

Fresh Mortar Density

1.7± 0.2Kg/L (+27°C)

(EN/SO 2811-1)

Layer Thickness

10 mm max.

Ambient Air Temperature

+5°C min/+35°C max.

Substrate Temperature

+5°C min/+35°C max.

Mature Time

15 Minutes

Pot Life

≥ 180 Minutes (100 g mass +27°C)

Open Time

>10 Minutes (EN 12004-2/ISO 13007-2)

Adjustability Time

8 Minutes

Applied Product ready to use

Use	Waiting Time
Grouting Floor/Walkability	24-36 Hours
Grouting Walls	4-6 Hours
Full Traffic	14 Days

Value determined at laboratory conditions:23°C ± 2°C, RH 50% ± 5%. Higher temperature will reduce the indicated waiting time, Lower temperature increase waiting time.

Important

Perfect from adverse weather conditions such as extremely high or low (Freezing) temperature, rain for at least 12-24 hours from application.

Consumption

Consumption is dependent on the substrate surface profile, roughness and application techniques As a guide for a single adhesive layer.

Size of Tiles	Notched Trowel Size	Powder Consumption
Small	6 mm	4.0–4.5 kg/m2
Medium	8 mm	5.4–6.0 kg/m2
Large	10 mm	7.5–8.0 kg/m2

Coverage

Pack	Area Covered
20 kg	34–40 sqft for 3 mm thickness
40 kg	70–80 sqft for 3 mm thickness

Cleaning of Tools

Clean all tools and application equipment with water immediately after use. Hardened/cured material can only be removed mechanically.

Mixing

• Pour the recommended amount of clean normal water into a suitable, clean mixing container
• Slowly add the powder to the water and then mix thoroughly using a low speed (< 500 rpm.) drill mixer until the material is fully mixed and lump free. Avoid entraining air into the mix by over mixing
• Allow the product to mature for 3-5 minutes before remixing for 30 seconds. The finished mix has a creamy consistency uniformly colored and is easy to apply and spread.